Replacement wood stock mini 14

It follows a series of helical grooves on the barrel, allowing the barrel tuner to be moved in and out. Turning the tuner clockwise moves it toward the receiver and counter clockwise moves it toward the muzzle.

The purpose of the heavy barrel and harmonic barrel tuner is to reduce the amplitude of the barrel arc. Barrel harmonics are vibrations of the barrel that occur during the firing of the gun and have a tremendous influence on accuracy.

These vibrations result in the barrel moving in an uncontrollable arc. If these barrel vibrations were consistent from shot to shot, only human error would stop your shots from becoming one-hole groups.

Unfortunately, these vibrations vary in magnitude and duration from shot to shot and result in inconsistent accuracy. The harmonic barrel tuner is able to offer even more help by its ability to move inward or outward on a barrel thus helping to reduce the amplitude of the arc. This in turn helps to make the bullet exit the barrel more consistently and therefore impacts favorably on its point of aim. With a barrel tuner you can fine tune your barrel so that the utmost accuracy can be obtained with any given ammunition.

Basically, a barrel tuner is accomplishing what a reloader is striving for, improved accuracy. Now that the accuracy problem with the Ruger Mini was satisfactorily solved, I finally fulfilled a thirty-year dream, ownership of a Ruger Mini I opted for the Target version with a Hogue synthetic stock.

I soon found out that it was possible to make the Mini into a one M. A rifle by carefully manipulating the harmonic barrel tuner and by determining what type of ammo it preferred. All is well, right? There are several issues which need to be addressed.

First, I was not crazy about the stock. Its design did not lend itself to the use of lasers, lights, red dot sights, vertical grips, etc. I want a stock that is equipped with picatinny rails so that I can mount any accessories that I need. A scope is not always the best sight of choice, but when I do use one I prefer to use a scope mount instead of the supplied rings.

A scope mount offers more flexible mounting options when compared to Rugers factory-supplied rings. When calling varmints in close-confined areas, I am greatly in favor of the use of red dot sights. A scout scope mount is the perfect solution to mounting a red dot sight. A red dot sight also works equally well in a home defense scenario.

Night-time hunting would not be the same and would not be as successful without lights and lasers that mount on your rifle. This is also true in a self-defense situation. Having the correctly equipped weapon, can mean the difference between life and death to you and your family! I will replace the recoil and hammer springs to decrease lock time and improve reliability. Along this same line of thinking, I will add a shock-absorbing polyurethane buffer.

To make magazine reloads easier, I will add an extended magazine release. Brownells makes it very easy for any shooter, experienced or not, to convert his Ruger Mini into a tricked-out rifle that meets your exacting wants and needs.

One stop shopping at its finest. The first step in this customization process is to determine what I am going to use the rifle for. Foremost, I wanted this rifle for varmint hunting, particularly night-time hunting. My secondary use is for self-defense purposes at home. The Tapco Fusion T6 Mini stock has a picatinny rail on the upper handguard that allows me to mount red dot sights, extended eye relief scopes, lasers, lights, etc. In addition, the bottom forend also has an integral picatinny rail so that I can mount vertical grips, lasers, and lights.

This sturdy lightweight stock also comes with an adjustable six-position collapsible buttstock. Length of Pull L. It is important to note that if you have a factory composite stock, you will need to purchase the stock reinforcement part stainless steel or This part is necessary when you use the Tapco stock.

At this point, I am ready to start disassembling our Mini Before you begin, I recommend that you first carefully watch the American Gunsmithing Institute AGI video or DVD There are several parts, when it comes to disassembling and reassembling the Mini, that can be tricky and difficult.

The AGI course will not only save you time, but patience. In addition, I have found that the Radocy Takedown guide is also very useful It is imperative that you have the proper tools before you begin disassembling any firearm.

Brownells has solved this problem by supplying a Ruger Mini Maintenance Field Pack When it comes to disassembling the Ruger Mini rifle you will find that it is unique compared to most firearms that you have taken apart. The removal of the trigger group will allow the rest of the rifle to be separated from the stock.

First, as always, check to make sure that the chamber is empty. Remove the magazine and cycle the bolt so that the internal hammer is cocked. Next, place the safety in the on-safe position safety is pushed back toward the trigger. Turn the rifle upside down so that the trigger is now facing upward. Trigger Guard in the Open Position. It will take some pressure to release the trigger guard.

Pull the trigger guard upward until it can no longer go forward. Tilt the back of the trigger group upward and remove it from the stock. The rest of the barreled action can easily be removed from the stock. When you pull the action out of the stock, the sheet metal forend liner will also come out.

Mini removed from the stock. This type of ammo usually have tougher primers which may not always fire with your factory hammer spring. First, you need to close and latch the trigger guard. Now restrain the hammer with your hand, push the safety to the fire position move it forward and pull the trigger to release the hammer. The punch will trap the hammer spring on the strut. Simply raise the front of the strut upward bringing the strut out of its recess at the rear of the hammer and thus out of the trigger group.

I then placed the hammer strut in the large hole in the center of the bench block found in your Mini maintenance field pack. I covered it with my hand to keep the spring from flying off and gradually pulled the punch out of the hole in the hammer strut. With the spring now separated from the hammer strut, I could replace the factory spring with the heavier Wolff hammer spring. Now the real problem began, how do I compress this heavy duty spring enough so that I can once again put the punch in the hole in the hammer strut???

I finally decided to try putting the spring and hammer strut in the vise and compressing it. Vise used to compress hammer spring. With the spring in the strut, I put the spring in the vise so that the strut was on top of the vise jaw. This way the spring could be compressed without harming the strut. While I tightened the vise jaws with one hand, I used my other hand to put pressure on top of the spring as added security. I continued until the hole in the strut became visible and I placed the punch back in the hole in the hammer strut.

Afterwards, I slowly opened the vise jaws and removed the spring and strut. To reinstall the hammer spring and strut, place the end with the punch in the recess in front of the secondary sear. Then place the front of the strut in the recess in the rear of the hammer and cock the hammer.

Now, you can remove the punch from the strut hole and you are finished. Since I already have the trigger group out, I will replace the factory magazine release. Accuracy Systems stainless steel or blue magazine release is considerably longer making reloads easier and faster. The only way to place the new release and spring back in place is to use a slave pin. The magazine release can not be replaced without one!

I found an old torx head wrench that was close to the same size and I cut a piece off with a dremel tool. Place the spring inside the release and drive the slave pin in place. Setting slave pin in magazine release. Make sure that you place the spring in the correct position since each end of the spring is different.

Since the spring will place the slave pin under tension unless the slave pin is much too small you will have to angle drive the slave pin in order to get it into the magazine release. The AGI course shows this process quite well. Next, you place the magazine release back in the same hole the stock release came from. Once again, this is not very easy to accomplish. You have to hold the release under tension in order to lineup the slave pin with the hole.

It took me several tries before I was able to drive the pin in thereby forcing out the slave pin. The next step is to remove the recoil spring and rod guide so that we can then remove the slide assembly. Once it is out of the hole, slowly release the tension and remove the guide and recoil spring from the slide assembly this is the part that the houses the recoil spring.

Move the slide assembly forward until its rear lug aligns with the disassembly notch on the receiver. Grab the bolt handle and pull the rear lug through the disassembly notch and move upward until the slide assembly is separated from the receiver. With a slight jiggle, it should come off. Showing how the slide assembly seats on the bolt. With the slide assembly out of the way, Option fair value calculation excel can replace the factory gas block with the Accuracy Systems tuneable gas block.

As you are aware, your Mini has a bad habit of throwing your brass 20 to 30 feet away. If you reload, you will spend considerable time running around trying to locate your brass. This tuneable gas block will enable you to throw the brass directly at your feet or as far as you want. Loosen the four screws that hold the two halves of the factory gas block together.

Be careful when you pull them apart because there is a small gas port bushing located within. After the upper and lower gas blocks are removed, place the gas port bushing in the barrel. Align the hole in the upper gas block with the gas port bushing and place it on the barrel. Align the lower gas block with the upper and tighten the factory allen head screws. When tightening, make sure that the gap between the upper and lower gas blocks are the same on each side.

Use a feeler gauge or a dial caliper to measure each side. Make sure that all four screws are securely fastened. It is critical that the gas block is tight and secure.

Simple and easy…well not exactly! The Accuracy Systems tuneable gas block was too stock market symbol caribou coffee for my series Mini Target rifle. My barrel diameter measured at the gas block was.

The changes that Ruger made in the Mini have been great, but the aftermarket manufacturers seem to be lagging behind. If you have an older Mini…No Worries Mate! Now that I have put the factory gas block back on, I am ready to install the new Wolff recoil spring.

The extra power Wolff recoil spring will increase lock time and kevin johnson stockbroker reliability.

Once again, a simple task turns out to be anything but!!! A spring is for a lack of a better word, springy! I tried to stuff it back into the slide assembly, but it was impossible to keep it in.

I hate to admit it, but I spent a couple of frustrating hours trying to get the spring to go back in with no luck. I really needed another set of hands to complete this task. Finally, I placed the slide assembly in a vise in order to free up my hands for working with the recoil spring and guide. I highly recommend a quality vise such as Brownells multi-vise and non-marring vise jaws Next, I had to figure out how to stuff the spring in the hole, hold it in place, and stuff more of the spring in until only the spring with the guide rod was protruding.

Then I could simply replace the guide rod tip into the hole located at the front of the receiver. Since I already had the recoil spring and guide out, I decided to add a Buffer Technologies recoil buffer The recoil buffer goes directly in front of the receiver where the recoil spring and guide rod are located. Buffer Technologies recoil buffer.

The purpose of the recoil buffer is to eliminate guide rod commonly known as an operating rod contact with the receiver. The recoil buffer offers less felt recoil, increased muzzle stability, less action noise, and extends the service life of your rifle. With the slide assembly in strategy for the binary options with tick charts vise I used two miniature needle-nose pliers to recall option in office 2010 the recoil spring into the slide assembly hole.

One plier was used to push the spring into the deep recessed hole in the slide assembly. Although it took me several tries, I finally managed to push almost all of the spring, except the section where the guide rod was, into the slide assembly hole. Next, I grabbed the guide rod with one hand and put it in the hole at the front of the receiver. I am sure there are other ways of accomplishing this same task, but this worked for me!

I have heard that there are some problems with this recoil buffer in some of the newer Minis. In some instances, the bolt will not stay open after the last shot. I reassembled the rifle and went to the range to test it. I fired a shot, but the spent case did not eject.

I used the old AR trick of removing stuck cases; I slammed the buttstock on the ground while simultaneously pulling the bolt back. Voila, the empty case ejected. I tried this several times with the same depressing results.

I tried two other magazines which also had the same failures. With the tighter tolerances on the new Minis, I believe that the recoil buffer is now too thick.

I have been told that if you experience this problem, you will need to sand the polyurethane buffer in order to reduce its thickness. In addition, the bolt has to stay open on the last shot. Hopefully, Buffer Technologies will soon remedy this problem for owners of the new Minis.

Ruger Rifle Stock Assembly Wood Recoil Pad Liner Ruger - MPN: MS

Since I have already made all the alterations to the rifle, I just have to install list of sebi registered stock brokers new Tapco Fusion T6 stockoptics both a scope and a red dot sighta technologically advanced green laser, and a state-of-the-art weapon light.

The Tapco Mini stock is made from military-grade composite and comes with a push-button six position M4 style buttstock.

It includes a straight stock extension for proper eye alignment when using a scope and an angle stock extension for open sights.

The SAW-type pistol grip has an internal storage area. The upper handguard has an integral picatinny rail, allowing wpr trading system use of optics, lasers, and lights.

The bottom forend has sliding cover which conceals another built-in picatinny rail. I am ready to begin assembly on the new Tapco stock. First, I need to reinstall the sheet metal forearm liner in the bottom of the Tapco stock. The stock reinforcement part stainless steel or now needs to be installed. Turn the stock upside down because it is easier to install the stock reinforcement from the bottom of the stock.

Magazine article on the stock market crash reinforcement in the Tapco stock bottom view.

I am now ready to place the barreled action in the Tapco stock. Insert the front of the stock into the bottom of the gas block. Press the barreled action into the stock until it is firmly seated. After making sure that it is properly placed, swing the trigger guard down until it locks shut you will hear an audible click.

Next insert the Tapco top cover with integral picatinny rail into the gas block and then push down until is fully seated against the stock. On the left side of the stock the third and only remaining replacement wood stock mini 14 screw and lock washer the other two were used in securing the stock reinforcement will secure the top cover to the lower stock. The right hand side uses a longer screw and a bushing which fills the gap between the top cover and the stock.

Tighten both screws tight, but not excessively. The next step is to fasten the buttstock to the stock body. There are two screws and nuts which bolt these two together. Lightly oil the screw before screwing it into the stock body. Screw it in until it becomes snug, do not overtighten. The newly outfitted Ruger Mini is now ready to be customized with our state-of-the-art accessories.

The TruGlo sight has a 5 MOA reticle that can be switched from red to green. The red dot increases sight visibility in bright conditions while the green enhances visibility in low-light. It has a twelve position brightness control that enables you to adjust the color as well pizza 73 work from home calgary to choose a brightness level which is compatible with your current conditions.

Due to its both-eyes-open design, the red dot sight makes it the perfect forexoma 1000 plan for fast-moving varmints or in self-defense.

Due to using the sight with both-eyes-open, you can still view the target and not lose sight of your surroundings.

mini 14 wood stock | eBay

This is especially true if are involved in an intruder self-defense situation. This sight is fitted with flip up lens covers that are see thru. If you are in an emergency situation and not thinking clearly, you will still be able to clearly see and identify your target.

Since the odds favor a night time encounter with a home intruder, a powerful blinding light is a necessity. I have used SureFire lights for several years and depend upon them on a daily basis. I equipped the Mini with felix baumgartner how much money did he make SureFire weapon mounted rail-mounted vertical grip weaponlight This is the finest weapons light available and it is easily attached to your weapon, via picatinny rail, by the A.

This comes forex crusher review with a and a lumen lamp assembly. The light can be controlled by several methods. First, there are two pressure switches located on the inside and outside of the vertical grip.

Closeup of Surefire Vertical Grip Weaponlight. Next, there is a switch located at the end xemarkets accurate binary option indicator the light. When it is turned counter-clockwise, the light will stay on. Also, the end cap located on the bottom of the vertical grip can be turned counter-clockwise if you wish to disable the light.

Located on top of the light are a pair of red LED seasonal futures trading strategies that can help you navigate around in the dark without compromising your position to an intruder.

They can be activated by pushing a pressure switch with your thumb. The switch is located at the rear of the weapon light at the top and rear of the vertical grip. Another advantage of the SureFire weapons light is its vertical grip. The vertical grip greatly enhances your control of your weapon, especially in close-quarters combat.

Every advantage that you have increases your odds of coming out alive when faced with a deadly encounter. The weapons light, especially with the lumen lamp assembly, makes the perfect night time varmint light.

Stocky's Rifle Stocks - America's Gunstock Specialists!

This powerful burst of light will temporarily blind and confuse your prey, giving you the perfect opportunity for a well-placed shot. In addition, as previously stated, the added stability afforded by a vertical grip allows you to make a steadier shot. Plus, the red LED lights enable you to maneuver in the dark without alerting wildlife. I have used red lasers for a number of years and been pleased with their performance.

The laser is highly useful in a high stress scenario such as an intruder in your home. Your weapon light disables the bad guy while your laser draws a bead on his vitals. Until recently lasers were all red. The red laser has its limitations. They are difficult to see in bright conditions. The sun tends to fade the red laser beam, making it difficult to see more than a few yards away. In subdued light, such as dark cloudy days, the red beam is visible up to thirty or so yards.

Best replacement stock for my Mini 14? - Shooting Sports Forum

Of course, in a dark house or when varmint hunting at night, the red laser is more than adequate. The future in laser lights is now; green lasers. As technology has advanced, green lasers have become affordable for the average consumer.

Although they still cost more they are smaller, offer greater visibility to the human eye, and more versatile in their uses. Under bright conditions, human eyes are approximately four times more sensitive to green than to red. This is even more pronounced under dark conditions.

A green laser beam is much easier to see in the dark or in bright sunny conditions at longer ranges than a red laser. The green laser is more temperature sensitive though. It operates best at temperatures between 40 and 0Fh.

A red laser operates between 10 and 0Fh. Batteries in a green laser last about one hour while red lasers can last up to three and half hours. Green lasers can appear as much as fifty times brighter than red lasers. Green lasers can be seen up to yards in broad daylight while red lasers will be visible only a few yards. As you can see, both lasers have their advantages and disadvantages. I have used a LaserMax red laser for several years and I have been completely pleased with its performance.

Since I primarily use my lasers outdoors, I am always looking for an affordable green laser. None was available until recently when LaserMax introduced the Uni-Max rail mount green laser sight LaserMax has increased the visibility of their green laser by pulsing the light.

Research has shown that light that is pulsed is much more visible to the human eye than a steady beam. Uni-Max Rail Mount Green LaserSight. This pressure sensitive switch replaces the sliding switch located at the back of the laser. Without the momentary activation switch, I have to take my hand off the vertical grip and manually slide the switch to the on position. This is not only awkward, but it distracts you and causes you to lose valuable time in a life-threatening situation.

To further increase the versatility of our Ruger Mini project gun, I added the time proven and old reliable standby; a rifle scope. Shooting accurately past yards is impossible without a good quality rifle scope. The next decision I had to make was whether to use the scope rings that came with the gun or to add a scope mount. I chose a scope mount for its versatility.

A scope mount allows you much greater latitude when mounting a scope. I have an extremely long Length of Pull L. A scope mount enables me to move the scope as far forward as I need.

Brownells has a great selection of scope mounts and I chose the Warne Ruger carbine base This mount attaches directly to the Ruger ring cuts in the receiver.

This weaver-style mount is simple, strong, and reliable. Warne Ruger Carbine Base mounted on scope ring cutouts. This will prevent the base from moving forward under adverse recoil. One of the most satisfying aspects of working with guns is the ability to customize your firearms to suit your individual needs. Not only do you feel as if you have accomplished something, but you now have a gun that truly reflects your personality. I know that I take greater pride in guns that have come to life in my hands.

If you would like a copy of the chat transcript please click "Send Transcript" below. Hello, to begin a chat session with a customer service representative, complete the fields below and click Chat. Brownells Sinclair Police Store Live Chat Live Chat. Create an Account Login Create an Account. Brownells Brownells 75th Anniversary - A Shooting Heritage Menu. AR Remington Ammunition Reloading Gunsmithing Tools.

By the Ruger Mini, chambered in. The Mini was born from the loins of two of the most popular and durable military rifles; the M and the M-1 Garand. The mini is a miniature version of the M and is a gas operated, magazine fed semi-automatic carbine rifle. It has an investment cast heat-treated receiver and a Garand breech bolt locking system with a short-stroke fixed-piston gas system. Close-up of Mini Receiver. Ruger Mini Target Rifle with Hogue Stock.

Mini Upper Handguard and Gas Block. Mini Harmonic Barrel Tuner. Brownells Ruger Mini Maintenance Field Pack. Close up of Trigger. Roll pin punch in hammer strut hole. Notch where the other end of hammer strut goes. Close up showing notch in hammer where strut goes.

Accuracy Systems magazine release, Factory magazine release, release spring, and pin. Removing factory magazine release. Slave pin in place. Slave pin driven out and replaced by magazine release pin. Slide assembly pushed toward muzzle exposing recoil spring. Now, grasping the bolt handle, slide it towards the muzzle exposing the recoil spring and the guide rod which is located inside the spring. This is a powerful spring and caution must be exercised when removing it from the hole which is located in the front of the receiver.

Process of moving slide assembly forward to remove it. Slide assembly in position to be removed from receiver. Muzzle view of Mini gas block. Gas block as viewed from the receiver. Side view of gas block. Hole in barrel where gas port bushing goes. Cover piece on bottom forend hiding picatinny rail. Exposed integral picatinny rail on bottom forend. Forearm liner positioned in Tapco Mini stock. Press down on end of forearm liner so that it snaps in place.

In order to insert the stock reinforcement I will need to squeeze it together. The lip of the stock reinforcement should rest on top of the forearm liner. Tapco supplies two screws with lock washers one on each side of the stock that will hold the stock reinforcement in place. Top view of stock reinforcement.

Note how it seats over top of the forearm liner. Shows how the stock slides into the gas block. Barreled receiver seated in the stock. Trigger group placed in the stock trigger guard must be open. Trigger guard pushed down and latched.

Short screw and lock washer securing top cover. Longer screw and lock washer bushing removed for clarity securing top cover on bolt side. Buttstock fastened to stock with 2 screws and nuts. Pistol grip positioned on stock. To increase the versatility of our Mini, I will configure it so that it conforms to our needs. First, I mounted an economical TruGlo 1x30mm dual color single dot sight on the picatinny rail located on the upper handguard.

Millet Buck Gold TRS x 50mm scope. National Shooting Sports Foundation Join the NRA National Rifle Association Childsafe. Visit our international partner sites. Close Chat Show Chat Hide Chat A A A. Thank you for contacting our Chat Team! Please visit us again. Hello, to begin a chat session with a customer service representative, complete the fields below and click Chat Name Please enter your name. Email Please enter your email. Question Please enter your question. In fact, I usually carry my Mini and maintenance kit in a Boyt gun case in my pickup truck.

Our first step in customizing our Mini is to replace the stock hammer spring with a Wolff extra power hammer spring The Wolff hammer spring gives you more striking force, thereby striking primers harder.

This is an absolute must when you are shooting steel-cased ammo such as Wolf. With the price of ammunition, I do a considerable amount of shooting with Wolf and other steel-cased rounds.

Firmly grasp the recoil spring and guide rod and pull backward removing it from the hole in the receiver. I have really been impressed with this scope. It is bright and clear and capable of much greater repeatable accuracy than I am capable of. The illuminated reticle is great for hunting at night, early in the morning, or late in the evening.

It also has a 30mm tube giving you extra windage and elevation that you will need if you do any long range shooting. Of course no tricked out conversion would be complete without high-capacity magazines. Brownells selection is second to known. Weapons Accessories has round and round steel magazines with a parkerized finish. John Masen offers round capacity magazines with a nickel finish and a black powder coating Pro Mag manufactures round and round polished blue steel magazines.